Weld Steel Green Machine

[R L Harris]

Hi to All Iam Rusty L Harris here is start of My build post!
Attached are photos of frame components and shop.
Iam currently painting the frame components as you see!

Similar Threads:

• New Machine Build- 6x12 weld steel hobbies build.
• The Green Machine!
• New Machine Build- No-Weld Steel 1 x 0.5 x 0.2m
• The Green Machine
• The Chicago Electric Weld Machine is good ???

[R L Harris]

Finshed painting legs and 8 braces tomorrow start painting table!
Ahren's Extended linear carriages arrived today

[R L Harris]

Finished Painting and reassemabled table

[TarHeelTom]

The table looks good so far.

Tom

[R L Harris]

I work for KC Store Fixtures as Design Engineer used thier metal fab shop to cut and weld the components!

[TarHeelTom]

Nice to have resources !

Tom

[CarveOne]

That's looking good R L. Is that a hammered finish green?

CarveOne

[R L Harris]

That's looking good R L. Is that a hammered finish green?

CarveOne

Bingo your correct Rust Oleum Hammered Finish!
Ill Get The 1/4" Rails Bolted on tonight and Attach the Gantry!

[CarveOne]

I thought it looked very familiar but the detail wasn't quite good enough to tell for sure. It has become a popular choice hasn't it?

CarveOne

[R L Harris]

Lost good camera could not find it anywhere so had buy me cheap
one for time being so it don't cut into mye funds for project lol!
Iam kind of parchel to color on tools easier to maintain since
hides miner flaws like nicks and scratches etc.

[R L Harris]

Well to tired get anything done tonight mye paying job took steam out of me
lol work 4 -10 hour days get 3 off except this week were going for the overtime to get more for project budget.

[R L Harris]

Dam mountig plates are short bye 5/8" do to incorrect measurement!
Lucky I made these to bolt on now have to go get 2 more chunks metal the right size redrill and tap so I can get gantry attached!

[CarveOne]

Dam mountig plates are short bye 5/8" do to incorrect measurement!
Lucky I made these to bolt on now have to go get 2 more chunks metal the right size redrill and tap so I can get gantry attached!

It happens to all of us. I could write a very depressing novel about some of my less than humorous escapades.

CarveOne

[R L Harris]

Daughter Called Said Grand Daughter Spent Evening In Emergency Room
Last Night Cost $500 Deductable on Insurance- Can We Borrow Some Money!

Sure ( Grumble ,Grumble) - Well be few more weeks ext. on build to
get rest of components know lol.

Bought Metal today remake the mounting plates for gantry!

[R L Harris]

Hi CarverOne got replacement plates need go machine them do that tomorrow!
Trying to relax tonight lol!

[R L Harris]

Ok in proccess of Make new plates blanks have been squared up on
mye mill just need to cut all holes in them and tap!

[R L Harris]

Need steel persuader like 5 or 10 pound sledge.
Lol dang corner on one end of side plate tweaks outward about 1/8" one or two good waps proably fix it lol but i don,t have one!
Neighbor does but he is out at the moment!

[CarveOne]

Need steel persuader like 5 or 10 pound sledge.
Lol dang corner on one end of side plate tweaks outward about 1/8" one or two good waps proably fix it lol but i don,t have one!
Neighbor does but he is out at the moment!

Sounds like my kind of precision alignment program. Wish I could lend a you hand with it.

CarveOne

[R L Harris]

Ok got gantry on it rolls slicker snot!

[CarveOne]

Ok got gantry on it rolls slicker snot!

In it's early days, WD-40 ran advertising in hunting magazines claiming "WD-40, Slicker than snot on a doorknob!" The first time I saw the ad I nearly split my sides laughing at that crude remark. It sure endured the brand in MY mind.

Sounds like the maul tweaks were successful. That's the thing I like about steel frame construction. Very workable material. When I only had a power drill and a hacksaw everything seemed like too much work and I hated it. With power hacksaw, MIG, Plasma torch, and milling machine on hand it has become much more friendly for me to work with for home projects.

CarveOne